Tab Content
  • timg's Avatar
    Yesterday, 07:00 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    It looks like Scott may have been on to something. From my reading about rectifiers on the interweb they should put out 15-15.5v DC or thereabouts....
    289 replies | 38810 view(s)
  • timg's Avatar
    24-09-2017, 09:50 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Thanks. Yep. In fact I put Wallace on to them. I've used the UltraBatt lithium batteries on all my previous buckets and my last couple of road bikes....
    289 replies | 38810 view(s)
  • timg's Avatar
    24-09-2017, 07:36 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Ok. Before I go buying more stuff to replace 'suspect' components has anybody got any ideas on what the problem may be? The bike runs well for...
    289 replies | 38810 view(s)
  • timg's Avatar
    23-09-2017, 10:30 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Well that's the BOB done and dusted for another year. A bit of a mixed bag :| This is my first DNF at the BOB :( On the positive the bike is quick...
    289 replies | 38810 view(s)
  • timg's Avatar
    22-09-2017, 08:14 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    It never rains when I bring wets :lol:
    289 replies | 38810 view(s)
  • timg's Avatar
    22-09-2017, 08:13 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Sufficient.... ;)
    289 replies | 38810 view(s)
  • timg's Avatar
    21-09-2017, 09:22 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Woohoo! :p All back together and looking promising. Just got to make spacers for the set of wets. See y'all at Levels on Saturday.....
    289 replies | 38810 view(s)
  • timg's Avatar
    20-09-2017, 08:33 PM
    timg replied to a thread parts needed in F4 Projects
    http://www.motorbikeparts.co.nz/index.php?route=product/category&path=79_78 Try Steve Ward for new Dunlops, he may have one or two.
    2 replies | 57 view(s)
  • timg's Avatar
    17-09-2017, 09:49 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Yeah, pretty much everything is set up the same as my FXR's, cam lift, duration & timing, same carb setup and similar jetting, same ignition and map,...
    289 replies | 38810 view(s)
  • timg's Avatar
    17-09-2017, 08:13 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Nah, binned the Megasquirt efi and have a carb and Ignitech - old skool and reliable I hope :)
    289 replies | 38810 view(s)
  • timg's Avatar
    17-09-2017, 05:16 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Getting there. The new inlet tract turned out to be a little too steep but an angled FXR carb rubber sorted that. Thanks Bren :) Had it on Wallaces...
    289 replies | 38810 view(s)
  • timg's Avatar
    16-09-2017, 09:44 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Kelford cams 'cos we already had them on hand....
    289 replies | 38810 view(s)
  • timg's Avatar
    13-09-2017, 10:29 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    Haha that's what the Aussie said it had. What a load of BS. If it has what my FXR had I'll be happy. I'll be even happier if I make it to the BOB....
    289 replies | 38810 view(s)
  • timg's Avatar
    13-09-2017, 09:45 AM
    timg replied to a thread Noob's FXR project in F4 Projects
    Engine is back :) New cams, valve springs, valve spring caps, cam chain tensioner, cylinder, piston, intake.... all kinds of buggeredupness sorted...
    289 replies | 38810 view(s)
  • timg's Avatar
    04-09-2017, 07:36 PM
    timg replied to a thread Noob's FXR project in F4 Projects
    I'll wave as you lap me :oops: or run you off the track :lol: Still waiting for stuff to turn up for my pig. New cams sorted. Piston & cylinder...
    289 replies | 38810 view(s)
  • timg's Avatar
    27-08-2017, 04:56 PM
    Anybody want some bucket tyres? Bridgestone slicks off my RS125. New for the Southern Classic Festival last year. Well worn on the left side but turn...
    1 replies | 152 view(s)
No More Results

2 Visitor Messages

  1. Hi Craig, sorry, don't come here much any more. Here's the guts of the 'Formula CAMS' class ormula CAMS 150/250. The class is for;
    250cc 4 stroke twins and singles
    150cc 2 stroke twins and singles
    Tyres and Chassis open
    A Class based on competition engines, motocross, GP125 etc
    B Class based on commuter engines as similar to F4
  2. View Conversation
    Hi Tim correct me if I am wrong but are you tied up with CAMS, if so do you know the tech rules of the new 250cc class I am hearing about. Keen to hear from you.

    Craig Hyde
Showing Visitor Messages 1 to 2 of 2
About timg

Basic Information

Date of Birth
January 18, 1960 (57)
About timg
Location:
Rolleston, New Zealand

Signature


Slower than James May

Statistics


Total Posts
Total Posts
852
Posts Per Day
0.28
Visitor Messages
Total Messages
2
Most Recent Message
11-11-2012 07:30 PM
Total Thanks
Total Thanks
29
  • Thanked 80 Times in 66 Posts
General Information
Last Activity
Yesterday 09:53 PM
Join Date
15-04-2009
Referrals
1